website Skip to content
Black Friday - Up to 60% Off Plus Extra 20% Off - Code BF20

Search Products

How to Take Down Vertical Blinds (and Fix Common Problems)

How to Take Down Vertical Blinds (and Fix Common Problems)

  • by 1ClickBlinds

To take down vertical blinds, open the slats so they face straight out, unhook each slat from its hanger at the top, then release the headrail from its brackets by pressing the clip or lever on each bracket and easing the rail down. It takes about 15 minutes for a standard window, and you only need a step ladder and, sometimes, a flat screwdriver. Most problems, such as slats that will not turn or a broken chain, can be fixed with one small spare part.

You might take down vertical blinds to wash the slats, move house, redecorate or fix a fault. The good news is that vertical blinds come apart easily, and you can put them back up in the same way.

How to take down vertical blinds: the quick answer

  • Time: about 15 minutes for a standard window.
  • Tools: a step ladder and a flat screwdriver.
  • Order: open the slats, remove the bottom chain, unhook the slats, then take down the headrail.
  • Tip: lay the slats flat in order so they go back in the same place.
  • Cleaning only? You can often clean the slats without taking the headrail down.

What you need

  • A sturdy step ladder
  • A flat screwdriver, for stiff bracket clips
  • A clean table or sheet to lay the slats on
  • A bag for the bottom chain and any small parts
  • A second person for long headrails over patio doors

How to take down vertical blinds step by step

  1. Open the slats. Turn the wand or pull the chain until the slats face straight out, at right angles to the window. This lines up the hooks so they come off easily.
  2. Remove the bottom chain. If your blind has a chain linking the bottom weights, unclip it from each slat and put it in a bag.
  3. Unhook each slat. Hold the slat near the top and push it gently up into the hanger, then slide it out sideways. Some hangers have a small clip you press instead.
  4. Lay the slats flat. Keep them in order and do not fold them, so the fabric does not crease.
  5. Find the bracket clips. Look at the top of the headrail where it meets each bracket. Most have a clip, tab or lever.
  6. Release the headrail. Press or turn the clip on each bracket, using a flat screwdriver if it is stiff, then tilt the headrail forward and lower it. Support the middle on a long rail.
  7. Remove the brackets if needed. Leave them on the wall if you are putting the same blind back. Unscrew them only if you are moving or replacing them.

How to put vertical blinds back up

  1. Clip the headrail into the brackets. Hook the front edge in first, then push the back up until it clicks.
  2. Turn the hangers so they face straight out, using the wand or chain.
  3. Hook each slat back on in the same order, pushing it up into the hanger until it clicks.
  4. Refit the bottom chain and weights so the slats hang evenly.
  5. Test it. Open, close and draw the blind a few times to check it moves smoothly.

How to fix vertical blinds: common problems

Problem Likely cause How to fix it
Slats will not turn Broken wand or hook, or a worn part in the headrail Replace the wand or its hook; if that is fine, the headrail mechanism may need replacing
A slat keeps falling off Slat pushed in only halfway, or a broken hanger Push the slat up until it clicks; if it still falls, the hanger is broken
Slats swing or twist Missing bottom weights or chain Fit new bottom weights and a bottom chain
Chain has snapped Broken chain or connector Join it with a chain connector clip
Slats bunch at one end End carriage has slipped Fit spacer bars to hold the carriage in place
Headrail is falling down Worn or loose brackets Tighten the screws or fit new brackets
Slats are torn, faded or stained Age and sunlight Swap in replacement vertical blind slats

Most of these parts cost a few pounds. See our blind spare parts, from bottom weights to wands and brackets.

Should you fix or replace a vertical blind?

Fix it if Replace it if
One or two parts are broken The headrail is cracked or bent
Only a few slats are damaged Many parts are worn at once
The blind still opens and turns You want a new colour or style anyway

Need a single slat? Read how to replace vertical blind slats. Ready for a new blind? Browse our made-to-measure vertical blinds.

Cleaning the slats while they are down

Taking the slats down is a good time to clean them. Lay fabric slats flat, dust them, then spot clean marks with a barely damp cloth. PVC slats can be wiped with mild soapy water. Let every slat dry fully before you hang it back up. For more tips, read how to clean vertical blinds.

Frequently asked questions

How do you take down vertical blinds?

Open the slats, remove the bottom chain, unhook each slat from its hanger, then press the clip on each bracket and lower the headrail.

How do you remove vertical blind slats?

Turn the slats so they face straight out, then push each slat gently up into its hanger and slide it out sideways.

How do you release a vertical blind headrail from its brackets?

Find the clip, tab or lever on each bracket, press or turn it, then tilt the headrail forward and lower it.

Why won't my vertical blinds turn?

The wand or its hook is often broken. If those are fine, a part inside the headrail may be worn and need replacing.

Why does a vertical blind slat keep falling off?

It is usually not pushed fully into the hanger. Push it up until it clicks. If it still falls, the hanger is broken.

Can I clean vertical blinds without taking them down?

Yes. You can dust and spot clean the slats while they hang. Take them down only for a deeper clean.

Do I need to take down the brackets?

No. Leave the brackets on the wall if you are putting the same blind back up.


Welcome offer

A little something
to get you started.

Scratch the panel below to reveal your first‑order discount.

Don't miss your discount